怎么讓Cisco3750交換機密碼初始化
怎么讓Cisco3750交換機密碼初始化
你還在為不知道怎么讓Cisco3750交換機密碼初始化而煩惱么?接下來是小編為大家收集的讓Cisco3750交換機密碼初始化教程，希望能幫到大家。
怎么讓Cisco3750交換機密碼初始化的方法
分類： 系統運維
1. 連接交換機的console口到終端或PC仿真終端。用無Modem的直連線連接PC的串行口到交換機的console口。
2. 拔掉交換機的電源.
3. 按住交換機上的Mode按鈕,與此同時,重新插上交換機的電源線.當交換機上SYST的LED長期亮的時候，可以松開Mode按鈕。
4. 再通過超級終端連接交換機。
5. 交換機有如下顯示：
switch:
:switch: flash_init
初始化flash文件系統
Initializing Flash...
flashfs怎么讓Cisco3750交換機密碼初始化: 83 files, 4 directories
flashfs怎么讓Cisco3750交換機密碼初始化: 0 orphaned files, 0 orphaned directories
flashfs怎么讓Cisco3750交換機密碼初始化: Total bytes: 15998976
flashfs怎么讓Cisco3750交換機密碼初始化: Bytes used: 6472704
flashfs怎么讓Cisco3750交換機密碼初始化: Bytes available: 9526272
flashfs怎么讓Cisco3750交換機密碼初始化: flashfs fsck took 8 seconds.
...done Initializing Flash.
Boot Sector Filesystem (bs) installed, fsid: 3
Setting console baud rate to 9600...
switch: rename flash:config.text flash:config.old
更名含有password的配置文件
switch: boot
啟動交換機
Loading "flash:c3750-i9-mz.121-19.EA1d/c3750-i9-mz.121-19.EA1d.bin"...@@@@@@@@@@
。。。。。。。。
--- System Configuration Dialog ---
Would you like to enter the initial configuration dialog? [yes/no]: yes
您是否進入初始化配置對話,選Y
At any point you may enter a question mark '?' for help.
Use ctrl-c to abort configuration dialog at any prompt.
Default settings are in square brackets '[]'.
。。。。。
Would you like to enter basic management setup? [yes/no]: yes
您是否進入基本配置安裝,選Y
Configuring global parameters:
Enter host name [Switch]: zcomf10
輸入設備的名字
The enable secret is a password used to protect access to
privileged EXEC and configuration modes. This password, after
entered, becomes encrypted in the configuration.
Enter enable secret: zcom:com
輸入密文
The enable password is used when you do not specify an
enable secret password, with some older software versions, and
some boot images.
Enter enable password: 12345678
輸入密碼(不能和密文相同)
The virtual terminal password is used to protect
access to the router over a network interface.
Enter virtual terminal password: 87654321
輸入虛擬終端的密碼(以備遠程登錄)
Configure SNMP Network Management? [no]:
詢問是否要設置路由器支持的各種網絡協議：
Current interface summary
。。。。。。。
Enter interface name used to connect to the
management network from the above interface summary: vlan1
鍵入作為管理接口的接口名
Configuring interface Vlan1:
Configure IP on this interface? [yes]: Y (對Vlan1進IP配置)
IP address for this interface: 192.168.10.1 (鍵入IP地址)
Subnet mask for this interface [255.255.255.0] :255.255.255.0 (鍵入子網掩碼,或按回車鍵使用默認值)
Class C network is 192.168.10.0, 24 subnet bits; mask is /24
Would you like to enable as a cluster command switch? [yes/no]: no (n集群模式?)
The following configuration command script was created:
已建立以下配置信息
hostname zcomf10
enable secret 5 class="main">
怎么讓Cisco3750交換機密碼初始化
enable password 12345678
line vty 0 15
password 87654321
no snmp-server
!
no ip routing
!
interface Vlan1
no shutdown
ip address 192.168.10.1 255.255.255.0
!
interface GigabitEthernet1/0/1
!
interface GigabitEthernet1/0/2
!
。。。。。。。。
end
怎么讓Cisco3750交換機密碼初始化 Go to the IOS command prompt without saving this config.
[1] Return back to the setup without saving this config.
[2] Save this configuration to nvram and exit.
這里有一個有趣的地方，那就是你能夠選擇進入命令行接口模式并放棄剛才的配置(0)，你也能夠回頭重新再設置一遍(1)，也能夠保存配置到NVRAM中并退出重啟(2)。這里我選擇的是0，我們將不保存剛才的配置并進入命令行接口模式(CLI)。接下來我們將介紹CLI。再重復一次，你可以在任何時候按下 Ctrl+C來退出安裝模式。
Enter your selection [2]: 2
Building configuration...
[OK]
Use the enabled mode 'configure' command to modify this configuration.
zcomf10>en
進入特權模式“en”或“enable”一樣
Password:
zcomf10#copy run
zcomf10#copy running-config star
zcomf10#copy running-config startup-config (退出,并保存到startup-config文件里:)
Destination filename [startup-config]?
Building configuration...
[OK]
zcomf10#reload (完成重啟)
Proceed with reload? [confirm]
看了“怎么讓Cisco3750交換機密碼初始化”還想看：