如何設置全網管網件路由交換機動態路由多區域OSPF
netgear網件是全球領先的企業網絡解決方案，及數字家庭網絡應用倡導者，那么你知道怎么去設置全網管網件路由交換機動態路由多區域OSPF嗎?下面是學習啦小編整理的一些關于如何設置全網管網件路由交換機動態路由多區域OSPF的相關資料，供你參考。
設置全網管網件路由交換機動態路由多區域OSPF的方法：
Netgear的全網管交換機中M6100、M7300、M5300均支持OSPF(M7300和部分型號的M5300需要通過對應的license升級啟用OSPF功能)
本文檔以一臺M6100和兩臺M5300(一臺M5300-28G3，一臺M530028GF3)為例說明如何配置多區域的OSPF。
物理拓撲和端口IP地址與單區域的文檔的配置相同，這里不再重復。但對邏輯拓撲做了細微改動。把M5300-28GF3的所有端口和M6100的2/0/1端口劃分到area 1。
修改后的拓撲如下：
M6100的OSPF配置
(M6100-3S) (Config)#router ospf
(M6100-3S) (Config-router)#enable
(M6100-3S) (Config-router)#router-id 1.1.1.1
(M6100-3S) (Config-router)#exit
(M6100-3S) (Config)#interface loopback 0
(M6100-3S) (Interface loopback 0)#ip ospf area 0
!在端口模式下把本端口宣告到OSPF的area 0
(M6100-3S) (Interface loopback 0)#exit
(M6100-3S) (Config)#interface loopback 1
(M6100-3S) (Interface loopback 1)#ip ospf area 0
(M6100-3S) (Interface loopback 1)#exit
(M6100-3S) (Config)#interface 1/0/1
(M6100-3S) (Interface 1/0/1)#ip ospf area 0
(M6100-3S) (Interface 1/0/1)#exit
(M6100-3S) (Config)#interface 2/0/1
(M6100-3S) (Interface 2/0/1)#ip ospf area 1
(M6100-3S) (Interface 2/0/1)#exit
(M6100-3S) (Config)#exit
M5300-28G3的OSPF配置
(M5300-28G3) (Config)#router ospf
(M5300-28G3) (Config-router)#enable
(M5300-28G3) (Config-router)#router-id 2.2.2.2
(M5300-28G3) (Config-router)#exit
(M5300-28G3) (Config)#interface loopback 0
(M5300-28G3) (Interface loopback 0)#ip ospf area 0
(M5300-28G3) (Interface loopback 0)#exit
(M5300-28G3) (Config)#interface loopback 1
(M5300-28G3) (Interface loopback 1)#ip ospf area 0
(M5300-28G3) (Interface loopback 1)#exit
(M5300-28G3) (Config)#interface 1/0/1
(M5300-28G3) (Interface 1/0/1)#ip ospf area 0
(M5300-28G3) (Interface 1/0/1)#exit
(M5300-28G3) (Config)#
M5300-28GF3的OSPF配置
(M5300-28GF3) (Config)#router ospf
(M5300-28GF3) (Config-router)#enable
(M5300-28GF3) (Config-router)#router-id 3.3.3.3
(M5300-28GF3) (Config-router)#exit
(M5300-28GF3) (Config)#interface loopback 0
(M5300-28GF3) (Interface loopback 0)#ip ospf area 1
(M5300-28GF3) (Interface loopback 0)#exit
(M5300-28GF3) (Config)#interface loopback 1
(M5300-28GF3) (Interface loopback 1)#ip ospf area 1
(M5300-28GF3) (Interface loopback 1)#exit
(M5300-28GF3) (Config)#interface 1/0/1
(M5300-28GF3) (Interface 1/0/1)#ip ospf area 1
(M5300-28GF3) (Interface 1/0/1)#exit
(M5300-28GF3) (Config)#
M6100上查看OSPF鄰居和路由表
(M6100-3S) #show ip ospf neighbor
Router IDPriorityIP AddressNeighborStateDead
InterfaceTime
-----------------------------------------------------------------------
2.2.2.21192.168.1.21/0/1Full/DR39
3.3.3.31192.168.2.22/0/1Full/DR35
(M6100-3S) #show ip route
Route Codes: R - RIP Derived, O - OSPF Derived, C - Connected, S - Static
B - BGP Derived, IA - OSPF Inter Area
E1 - OSPF External Type 1, E2 - OSPF External Type 2
N1 - OSPF NSSA External Type 1, N2 - OSPF NSSA External Type 2
C 10.1.1.1/32 [0/1] directly connected, loopback 0
C 10.1.2.1/32 [0/1] directly connected, loopback 1
O 172.16.1.1/32 [110/2] via 192.168.1.2, 00h:27m:00s, 1/0/1
O 172.16.2.1/32 [110/2] via 192.168.1.2, 00h:27m:00s, 1/0/1
O 172.16.3.1/32 [110/2] via 192.168.2.2, 00h:25m:53s, 2/0/1
O 172.16.4.1/32 [110/2] via 192.168.2.2, 00h:25m:41s, 2/0/1
C 192.168.1.0/24 [0/1] directly connected, 1/0/1
C 192.168.2.0/24 [0/1] directly connected, 2/0/1
M5300查看OSPF鄰居和IP路由表的方法與M6100相同，從M6100的輸出信息可以看到，鄰居建立正常，路由表正確。
看過文章“如何設置全網管網件路由交換機動態路由多區域OSPF”的人還看了：
2.思科OSPF功能介紹及配置
3.詳解OSPF路由器完全鄰接關系的建立過程
8.路由器常識全解
10.華為路由器詳細介紹